The silicone wax making form 390 x 260 mm is sprayed up from the inside with some soapy liquid that reduces wax sticking. Melted liquid wax is poured onto the bottom sheet with a spoon - spreading is done from the inner part to outside. Then the upper part of the form is gently pressed from above. The residual wax is being pushed out of the form onto the board. To have the wax foundation made up even and smooth, some kind of domestic (or even paper) roller may be used - it is rolled over the form's surface from above. After wax solidifies, the ready made wax foundation is removed by slowly pulling up the top sheet, and at the same time the wax foundation is held by a hand to separate it from silicone.

Country of origin – Bulgaria.

The post Wax foundation making silicone form “BG” (390 x 260 mm) without circulation pump for cooling appeared first on wilara.

Power supply: power 20 W/230 V, maximum power 30 W. Power cord 230 V has a handy on/off switch. Power cord length approx. 150 cm.

Output voltage: 24 V / 0.83 A (1.25 A max.). Suits for stainless wire – 0.3/0.4/0.5 mm in diameter. Has contact spikes. Working length is approx. 100 cm.

Note. The workspeed depends on the wire diameter, length, wax foundation sheet thickness and ambient temperature. The transformer heats up during operation. After ten honeycombs embedded, required to do 15-20 min. breaks. Has a thermal protection - after turning off, it turns on again, when it cools down.

Country of origin - Poland.

The post Electric wax embedder 20 W HTS 20/003M (20 W / 230 V ˃ 24 V) appeared first on wilara.

Power supply 45 W/230 V, maximum 85/80 W. Power cord with convenient on/off switch. Power cord length about 150 cm.

Output voltage: 12 V (for galvanized) or 24 V (for stainless) - switched by a switch on the transformer housing. With contact spikes. The length of the wires is about 50 cm.

Note. Workspeed depends on the diameter and length of the wire used in the frame, as well as on thickness of the wax foundation and the ambient temperature. The transformer heats up during operation: after 20 embedded combs, required to take 15–20 min. breaks. Has a thermal protection – if overheating 110ºC occurs, turns on again once it cools down.

Country of origin - Poland.

The post Electric wax embedder 45 W HTU 45/011M (45 W / 230 V ˃ 12 V / 24 V) appeared first on wilara.

Power supply 65 W/230 V, maximum 105/95 W. Power cord with convenient on/off switch. Power cord length about 150 cm.

Output voltage: 12 V (for galvanized) or 24 V (for stainless) – switched by a switch on the transformer housing. With contact spikes. The length of the wires is about 50 cm.

Note. Workspeed depends on the diameter and length of the wire used in the frame, as well as on thickness of the wax foundation and the ambient temperature. The transformer heats up during operation: after 20 embedded combs, required to take 15–20 min. breaks. Has a thermal protection – if overheating 110ºC occurs, turns on again once it cools down.

Country of origin – Poland.

The post Electric wax embedder 65 W HTU 65/011M (65 W / 230 V ˃ 12 V / 24 V) appeared first on wilara.

Input: power 65 W/230 V, maximum power 95 W. Cable with a convenient power (on/off) switch. Power cable length about 150 cm.

Output: 24 V / 2.71 A (for stainless wire). With contact spikes. Working cable length about 90 cm.

Note. Workspeed depends on the diameter and length of the wire used in the frame, as well as on thickness of the wax foundation and the ambient temperature. The transformer heats up during operation: after 50 embedded combs, required to take 15–20 min. breaks. Has a thermal protection - if overheating 110ºC occurs, turns on again once it cools down.

CE certified. Country of origin – Poland.

The post Electric wax embedder 65 W INOX HTS 65/003M (65 W / 230 V ˃ 24 V) appeared first on wilara.

Power supply: power 100 W/230 V, maximum power 130/110 W. Power cable 230 V has convenient on/off switch. Power cable length approx. 150 cm.

Voltage output: 12 V (for galvanized wire, 2–4 sec.) and 24 V (for stainless wire, 2–4 sec.) – a 12V/24V switch on the transformer housing. With contact spikes. Cable length approx. 50 cm.

Note. The workspeed depends on the diameter and length of the wire in frame, as well as thickness of the wax foundation and ambient temperature. The transformer heats up during operation. After 50 embedded frames, requires to take a 15-20 min. breaks. Has a thermal protection - after overheating, when it cools down, turns on again.

CE certified. Country of origin - Poland.

The post Electric wax embedder 100 W HTU 100/011M (100 W / 230 V ˃ 12 V / 24 V) appeared first on wilara.

Input: power 80 W/230 V, maximum power 130 W. 230 V power cable with on/off switch. Power cable length 150 cm.

Output: 12 V / 18 V (galvanized wire 0.3/0.4/0.5 mm) or 24 V / 36 V (stainless wire 0.3/0.4/0.5 mm) - inserted into the appropriate socket on the transformer housing: red comes to zero, black to the required one. Contact ends with spikes. The wires from the transformer reach about 80 cm.

Note. The wire embedding speed depends on the diameter and length of the wire in a frame, as well as on thickness of the wax foundation and the ambient temperature. The transformer heats up during operation. It is essential to take 15-20 min. breaks after some 50 combs embedded. It has a thermal protection of 110ºC - after overheating, it turns on again when it cools down.

CE certified. Country of origin - Poland.

The post Electric wax embedder MULTI-UNIVERSAL HTM 80/001M (80/max. 130 W / 230 V ˃ 0/12/18/24/30/36 V) appeared first on wilara.

Input 230 V. Output 24 V AC/ 60 W.

Country of origin - Italy.

The post Electric wax embedder 60 W (230 V ˃ 24 V / 60 W, with overheating protection) appeared first on wilara.