nuotraukos padidinimo mygtukas

Radial honey extractor „PREMIUM Line“ Ø 1500 mm (88 frames, automatic steering)

# 121721

6,039.00 

Out of stock

Cylinder’s diameter 1500 mm. Electric drive on the bottom, directly connected to the rotor axle.
Frame is made of steel, painted with electrostatic painting technology, it is stable and easy to disassemble. Cylinder height 725 mm. Weight 193 kg. Dimensions: 1900 x 1625 x 1135 mm.
The ball valve 3 inches (76 mm) in diameter for honey draining.
Radial rotor made of stainless acid resistant steel rods Ø10 mm. The rotor inserted in the bushings on the bearings at the top and bottom.
The transparent lid is 8 mm thick, embedded with eight stainless hinges.
Legs are of stainless steel: 1 100 x 60 x 40 mm.
Power: 2.2 kW / 230 V / 90/10/90.

The exclusive Premium Line honey extractors made of the best quality materials and components. Their most distinctive feature – durability, reliability and excellence at work. This device radially can accommodate 88 deep or shallow frames. The gear which is located underneath the bottom consists of a high-performance motor gear series THF eco-line, directly coupled to the axis of the rotor and an E1000 series voltage frequency inverter – all enable for the full optimization of the system. The implemented gear drive reduces power consumption down by 35%, while still retaining the excellent technical parameters of the Premium quality honey extractor. By using the gear of the series THF was increased the durability of the device, and this also reduces the noise level significantly. More reliable electronics were installed to the extractors’ control.

Extractor’s stand is made of stainless steel. It is very stable and easy to dismantle. The drum itself is made of thicker acid resistant stainless steel – 0,8 mm thick, strengthened and reinforced sheet, with ball valve drain Ø3 inch (76,2 mm). The bottom is conical, also acid-resistant, 1 mm thick, stainless steel. Transparent lids, made of meta-plexi glass 8 mm thick, allowing safely to observe the spinning process, without any risk of contact with the rotating basket, and also protects against the undesirable formation of honey mist in the working premises.
The radial basket is made entirely of stainless steel acid-resistant rods and plates. Rings of the rotor are equipped with properly shaped frames’ resting plates, preventing them from falling during the spinning. Its axis is journaled in two housings: the upper and lower. The entire rotor is reinforced in its construction.

An advanced automatic steering HE-03 is installed. The HE-03 steering is equipped with the latest electronic processor. It has been designed to provide the user with unsophisticated, but intuitive and reliable device.
The main HE-03 features and advantages: (1) 8 fully programmable automatic spinning cycles; (2) Large (4,3’’) TFT graphic display with energy-saving LED illumination; (3) Screen resolution: 480×272 pixels; (4) 8 ergonomically designed steering buttons; (5) Easy to use and intuitive interface with high-resolution icons displayed, that enable its viewing in any lighting conditions; (6) The graphic editor for spinning cycles and built-in autocorrection editor for parameters; (7) Two independent timers to measure the extractor’s working time; (8) Advanced diagnostic-controlling functions for constant monitoring of the steering parameters; (9) The high quality vector inverter from Mitsubishi company is guided therein.

The automatic steering control allows the operator to choose any of the personally programmed his own programming cycles (namely, the programs from the 4th to 8th). The first two programs allow to handle spinning direction, speed and time manually. The third one is an automatic one and has factory settings. For any of spinning cycles it is necessary to set 7 steps. Each step is defined by the three parameters: cycle starting time, given speed and spinning direction (the last seventh step determines the rotor stoppage time – can not be changed).

Complies with all EU requirements.

Manufactured by Poland.